LR Toe Set Tool kit (ASSEMBLY)

Sale Price $64.74 Regular Price $71.93
100+ In Stock
SKU
DIY-TST

DIY Alignment Toe Set Tool Kit (LROR)

Going off road means things are going to get bent, loosened up, and need repair.  It would get expensive fast if you had to take your truck in for alignment every time you worked on the front end.

While camber and caster can be adjusted on most vehicles, there is not much adjustment for camber on solid axle trucks. While caster can be adjusted either with control arms on 4- and 3-link trucks or with leaf spring shims on leaf spring trucks, toe is sometimes hard to adjust without help or a special tool.

For all of these reasons, there is the DIY Alignment Toe Set Tool. To use, just follow these simple steps:

  • Put your vehicle on jack stands
  • Remove the wheel
  • Bolt the tool to your hub
  • Align the tool side to side at the same level
  • Apply brakes
  • Use tape measure to check toe in and toe out as well as total toe
  • To find camber, rotate the tool up and attach a magnetic angle finder

Works great and saves you money!

Most vehicles are approximately 1/8-1/4" total toe in. We like to run about 1/8" toe in to avoid tire wear since incorrect toe is the major cause of tire wear on any vehicle.

This kit includes (2) toe alignment plates - laser cut and zinc plated for corrosion resistance.

Center Hole Diameter: 4.5"
Lug Hole Diameter: 1/2" (can be drilled larger for larger lugs)

Bolts to:

  • 5 on 4.5 (Jeep Wrangler YJ/TJ, Cherokee, Grand Cherokee, Patriot, Liberty)
  • 6 on 4.5 (Dodge Ram & Nissan Xterra, Frontier, Pathfinder)
  • 5 on 5.0 (Jeep Wrangler JK)
  • 5 on 5.5 (Suzuki Samurai & Jeep Wrangler CJ)
  • 6 on 5.5 (Most Toyota 4x4s)
  • 8 on 6.5 (for larger pickups)

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

  • Kit includes (2) toe alignment plates
  • Laser cut and zinc plated for corrosion resistance
  • Center Hole Diameter: 4.5"
  • Lug Hole Diameter: 0.5" (can be drilled larger for larger lugs)

Fits most vehicles with the following bolt patterns:

  • 5 on 4.5
  • 6 on 4.5
  • 5 on 5.0
  • 5 on 5.5
  • 6 on 5.5
  • 8 on 6.5

All products carry our 12 Month Limited Warranty. All warranties are limited to the original purchaser and are not transferable to subsequent owners of the product. The warranty period begins on the purchase date. Trail-Gear warrants that it will repair or replace, free of charge, any eligible product which, under normal conditions of use and service, proves to be defective in materials or workmanship. This warranty does not cover any labor costs incurred in diagnosis of defects, removal or reinstallation of a product, nor does it cover any other consequential expenses.

Please read and review our return and warranty requirement document before sending in products.

Warranty Exclusions


Trail-Gear Inc. warranty does not cover, and Trail-Gear Inc. shall not be liable for, any undertaking, representation, or agreements made by dealers or other third parties selling Trail-Gear products, except where such agreements are within the provisions of this Warranty.

Specifically excluded from this warranty are failures caused by lack of maintenance, misuse, negligence, modification, abuse, improper application, crash damage, installation or operation, or failures caused by unauthorized service or use of unauthorized parts.

Additionally excluded from this warranty are parts which are subject to normal wear and tear, such as bushings, fluids, hoses, gaskets, belts, etc. Products not manufactured by Trail-Gear Inc. are excluded from any warranty and shall be handled with the original manufacturer.

All parts used in a competitive racing environment are excluded from this warranty. If, after inspection, a part returned, under any warranty, is deemed to be ineligible for warranty repair or replacement, the part may be repaired or replaced for a discounted cost. Return shipping charges will apply. Any part for which a warranty replacement is sought must be returned to Trail-Gear Inc. before any replacement items can be shipped. All replacement parts shipped before the suspect part has been received and evaluated by Trail-Gear, MUST BE PAID IN FULL. In such a case, after the suspect part has been received and approved for a warranty replacement, the purchase price for the replacement will be refunded.

    To begin your warranty claim:
  • Please contact Trail-Gear Inc. at 559-252-4950 or email [email protected] prior to returning any product under warranty to verify that warranty is still in effect.
  • Products must be shipped back to Trail-Gear Inc. at the expense of the customer.
    Ship all products to:
    ATTN: WARRANTY
    5356 E. Pine Avenue
    Fresno, CA 93727.
  • Please place a clearly marked copy of the original invoice inside the package.
  • Please include a short note stating the problem you are experiencing.

If any of the above mentioned policy is not met, the package will be refused or warranty claim denied. By completing the steps above, this will ensure faster processing of your claim so that Trail-Gear can get your product back to you as quickly as possible. All warranties are generally processed within 2-3 business days of Trail-Gear receiving the parts from you. Additional delays may be incurred if product needs additional testing or repairing.

If you are an international customer, please email the warranty department at [email protected] to receive further instruction. International customers may have the option to field destroy an approved warranty to avoid costly return shipping. In this case, any shipping charges for replacement parts will be at the expense of the customer.

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
Copyright © 2021 Low Range Off-Road. All Rights Reserved.